­
Additional position light for Scania LED foglight 2016-2022 - Matronics

Truck 24V

  • Indoor lighting
  • Outdoor/Waterproof
  • Warning lighs
  • Lamps and lights
  • 24V LED bulbs
  • Halogen bulb
  • Poppy & Wunder-Baum
  • Hella lights
  • Reflexes
  • Interior styling
  • Exterior styling
  • Connectors and accessories
  • Scania Special
    • Scania 2023+
    • Scania 2016-2022
    • Scania -2016
  • Volvo Special
  • Mercedes Special
  • MAN special
  • DAF special
  • Iveco special
  • Controllers
  • Trucker gear

Additional position light for Scania LED foglight 2016-2022

SKU: 240878-AM

Emitters with 18 bright LEDs, specifically developed for the original Scania LED foglights. The emitters are available in xenon white, yellow and warm white, lights up the whole reflector of the foglights. The light is not blinding and works as position lights. The clever design allows you to fully keep the function of the foglight.

The emitter is placed on top of the existing emitter for the fog-light. Screws and spacers are included, and are required for mounting. 

Single color, Yellow/White/Warm white

There is 3 meter wire on each emitter, that can be connected to the regular positionlight. There is a plus and minus wire.

Mounting

Remove all screws from the top of the lamp

The heatsink is glued on to the lamp, so you must cut it along the edge with a hobby knife. See the photo of the heatsink from above, where it is marked with a red dashed line where you need to cut. Break the lamp apart, eg. use two flat screwdrivers to make the glue tear apart.

Remove as much original glue as possible.

Drill a hole in the lamp as marked. It is an advantage to drill in between two heat sink ribs, as this makes gluing the wire easier. Feed the cable from the emitter through. Make sure not to ruin the cable-jacket. It can be an advantage to countersink the hole first. Make sure to seal the hole again.

Remove the two outer screws on the original emitter, and place the two spacers over the holes. Put the new emitter on top of the existing, with the LEDs placed outwards. The emitter is fastened using the included M4x8mm screws. The lamp is glued and screwed together again.

Connect the lamp, eg. to the existing position light.

Fits models from 2016-2022. It is important to use the included screws and spacers, as you risk the emitter to break otherwise.


Emitters that fits into the original Scania LED foglights. The lamps are opened and the emitters is placed on top of the original. Fits models from 2016-2022.

Vis fuld beskrivelse


Pick

 
 
 
 
 
 
 
 
 

Prices per set

at 1 set DKK 995,00

Set

Retail price: 995,00 DKK


Catalogue

Download catalogue

Troubleshooting supplemental position light

Before you start

Control that all parts are correctly connected, and that all plugs are completely joined / screwed together. You should never connect the emitters to 24V directly, as the stobelight will burn off, without a controller.

Isolate the error

If one of the emitters work, try to swap the controller outputs, to check if the error is on the emitter or the controller.

Controller not working

Check the fuse inside the controller. This can be done with the Continuity-tester / beeper.

Emitter not working

Check that all the wires are connected to the emitter. If a wire is loose, you can solder it on to the board. If you are in doubt about the connection, contact us.

Position light not working

Check all wires. If all LEDs on the position light is not working, it should be the power supply to the board that is failing.

If there are only some LEDs that are not working, the board is defective.

Strobe light not working

Check all wires. If the other emitter works, try to connected the failing emitter to the other output. If the strobe is still not working, the emitter is defective.

has been put in basket


Fetching related products...